Part:BBa_K4361009

BlcR-binding oligo, 51 bp, IR1 perfect RV 2 outer 5 + IR2

BlcR is a transcription factor originating from the bacterium Agrobacterium tumefaciens (Part:BBa_K4361100). In a homodimer state it contains a single DNA-binding domain that specifically binds one of two DNA sequences. Both sequences are so-called inverted repeat pairs (IRs), short DNA sequences whose ends are reverse complements of each other. For the Blc operator, these sequences are 'ACTCTAATgATTCAAGT' (IR1) and 'ATTAGttgaactCTAAT' (IR2), as further explained in Part:BBa_K4361001.
As described in Part:BBa_K4361004 and Part:BBa_K4361005, the original sequence of IR1 is not a perfect reverse complement of itself. Furthermore, as described in Part:BBa_K4361007, only the outer 5 nucleotides of IR2 are reverse complementary instead of the outer 8 in IR1, meaning IR1 can be changed to also only have its outer 5 nucleotides be reverse complementary. This part has been designed to combine the changes in Part:BBa_K4361005 and Part:BBa_K4361007, meaning nucleotides 6-12 of IR1 RV 2 have been replaced by those of IR2, resulting in 'ACTTGttgaactCAAGT' (IR1 RV 2 outer 5). The BlcR-binding domain of this part thus consists of IR1 RV 2 outer 5-tca-IR2, where tca is the original 3 nt linker sequence between IRs.

Sequence and Features

Assembly Compatibility:

• 10
  COMPATIBLE WITH RFC[10]
• 12
  COMPATIBLE WITH RFC[12]
• 21
  COMPATIBLE WITH RFC[21]
• 23
  COMPATIBLE WITH RFC[23]
• 25
  COMPATIBLE WITH RFC[25]
• 1000
  COMPATIBLE WITH RFC[1000]

Usage and Biology

The blc operator contains 2 pairs of inverted repeats, linked together by a 3 nt spacer, and each pair is assumed to bind one BlcR dimer (see Part:BBa_K4361100). With a spacer of specifically 3 nt, the centers of each pair are exactly 20 nt apart, which supports the hypothesis that the two dimers orient themselves at the same rotation angle to the DNA to form a tetramer. If the spacer were of a different length, the dimers would have different orientations to each other, possibly inhibiting tetramerization (see Part:BBa_K4361014). With two BlcR dimers bound and forming a tetramer, RNA polymerases originating from an upstream promoter are hindered from transcribing past the blc operator, inhibiting expression of downstream blcABC genes. Each BlcR monomer contains a binding site that is specific to gamma-butyrolactone (GBL) gamma-hydroxybutyric acid (GHB) and succinic semialdehyde (SSA). When a BlcR tetramer binds GHB with one of its binding sites, tetramerization is inhibited and BlcR becomes dissociated from the DNA, enabling downstream transcription and subsequent digestion of the newly present substrate (see Figure 1).

Figure 1. General overview of the unbinding mechanism of BlcR from DNA in the presence of SSA. Left: two BlcR dimers bound to DNA as a tetramer. Middle: SSA is introduced into the system. Right: BlcR dimers bind SSA and unbind from the DNA.

In our project, these oligos are used to tether BlcR to the surface of a gold electrode, of which we measure the capacitance. When BlcR molecules dissociate from the DNA in response to the binding of GHB, water molecules are displaced towards the surface of the electrode, which causes an increase in capacitance. This is the signal we interpret to indicate the presence of GHB.

Oligo variants
The wildtype blc operator has been theorized to not bind BlcR optimally, since BlcR regulates its own expression and that of proteins involved in the breakdown of GHB-like molecules. This means BlcR has to quickly unbind if these molecules taken up by A. tumefaciens, such that the bacterium can digest the molecules for nutrients. In our system, however, we would like BlcR to be more stably bound to DNA, such that it will only unbind in the presence of high GHB concentrations. This can be accomplished through two approaches: adjusting BlcR itself (see Part:BBa_K4361200 through Part:BBa_K4361227 and Part:BBa_K4361300 through Part:BBa_K4361319), or changing the DNA molecule it binds to. This set of Parts, ranging from Part:BBa_K4361000 up to Part:BBa_K4361022, shows our work on the second approach.

Results

As described in the Results section of Part:BBa_K4361000 and Part:BBa_K4361001, an electrophoresis experiment was performed with the majority of our designed oligos, wherein the aforementioned parts act respectively as the negative and positive control. By incubating them with BlcR and running them on a gel, the binding strength of BlcR to each sequence can be estimated by looking at the bands of free DNA and DNA bound by the protein. As can be seen in Figure 2, the amount of DNA bound by BlcR is comparable to that measured for the wildtype oligo. This suggests a similar binding affinity between BlcR and DNA, so this oligo was selected to be further analyzed, as described below.

Figure 2. Results of the electrophoresis experiment in which the fraction of DNA bound to BlcR was determined for different types of oligos. The first bar and bottom dashed line represent the results with Part:BBa_K4361000 (scrambled oligo, negative control), the second bar and top dashed line correspond to those with Part:BBa_K4361001 (wildtype oligo, positive control). The third bar depicts the measured fraction of bound DNA for this part. Values represent the ratio between the intensity of the band corresponding to protein-bound DNA, and the sum of the protein-bound and protein-free bands.

In a second electrophoresis experiment, two runs were done for the two controls and five selected oligos that showed binding similar to or increased from the wildtype (Part:BBa_K4361007, Part:BBa_K4361008, this part, Part:BBa_K4361021, and Part:BBa_K4361022). One run was performed under similar conditions as those in the experiment described above, while SSA was added to the second run. As a substitute for GHB, it is expected that the addition results in the separation of BlcR tetramers into dimers, leading to them unbinding from the DNA. Indeed, Figure 2 shows that this is the case for all samples. More strikingly for the selected oligos, the amount of bound DNA drops from increased levels when compared to the wildtype oligo to similar levels after addition of SSA. This means that there is a relatively larger change in the amount of bound DNA, which would be beneficial for application in an electronic biosensor as the bigger change in the signal would be easier to measure.

Figure 3. Results of the electrophoresis experiment in which the fraction of DNA bound to BlcR was determined for different types of oligos in the presence or absence of 25 μM SSA. The first set of bars represents the results with Part:BBa_K4361000 (scrambled oligo, negative control), the second set of bars corresponds to those of Part:BBa_K4361001 (wildtype oligo, positive control). The third set depicts the measured fraction of bound DNA for this part. Values represent the ratio between the intensity of the band corresponding to protein-bound DNA, and the sum of the protein-bound and protein-free bands.

For further details on the experiments with our DNA oligos and the results, see the Results page on our wiki.